No Colour Selected

Choose Colour

DULUX TRADE TUFFCOTE EPOXY

Chemical resistant finish coat on steel and concrete surface.

DULUX TRADE TUFFCOTE EPOXY

Name: DULUX TRADE TUFFCOTE EPOXY
SKU: 2323
Price: 18900.00 NGN
Availability: InStock

₦18,900.00

Chemical resistant finish coat on steel and concrete surface.

Find a colour for this paint

SKU: N/A Categories: Water-based, Position, Product Type, Interior, Steel, Specialty Products, Surface, Finish, Gloss Tags: The cured film is non-toxic (contains no lead or other toxic chemicals), Environmentally friendly, Equipment is cleaned with water, Almost odourless during application and curing, The substrate can be damp – concrete need not be fully cured before application., Non-specialist application – can be applied by the average “do-it-yourselfer”, Water-based, Resistant to fresh and salt water + oils and chemicals when fully cured – withstands continuous immersion up to 60°C, Withstands nuclear radiation and is easily decontaminated, Completely free of Mesityl Oxide and is therefore approved for use in breweries

How much paint do I need?

Do you know the area?

Key Information

Finish Gloss

Coverage At 50 μm DFT: Brush approx 9.3m per litre / Spray approx 6.8m per litre

Drying Time 24 hours minimum; up to 7 days maximum

Coats 2

Product Description

Tuffcote epoxy is an environmentally friendly, water-based epoxy . Chemical resistant finish coat on steel and concrete surface. Almost odourless during application and curing. Resistant to fresh salt water, oils and chemicals when fully cured.

Application Description

Cleaning of equipment
For clean up use potable water.
Substrates
Suitable for cement plaster, concrete and metal surfaces.
Precautions
Ensure that surfaces are sound and free from dust, dirt, grease and oil. Surfaces must be thoroughly dry – no more than 12% moisture content.
Do not apply during cold (below 10°C) or wet weather.
Do not apply directly to bare metal surfaces.
Recommended for interior surfaces only.
Cure is slow at low temperatures; below 15°C it takes some days to reach handling and recoating hardness.
High temperatures will shorten pot life and drying times, while low temperatures and high relative humidity will lengthen drying time. The relative humidity must be below 90% during application.
Equipment and brushes must be cleaned immediately with tap water.
Only suitable for interior use – the film tends to yellow and chalk on exterior exposure.
Not suitable for direct application to powdery or friable surfaces whether previously painted or not.
Application
Tuffcote is packaged in two components in the proper proportions which must be mixed together before use.
Stir the upper container thoroughly, then add to the Curing Agent in the lower container and mix until uniform.
Do not mix more material than will be used within 1 hour.
N.B. The end of the pot life will not be shown by a viscosity increase (gelation). Material must be used within 1 hour.
Airless Spray: Apply direct as supplied, using a 0,533 mm or larger tip. If necessary, thin up to 15%.
Brush: Ready for use when mixed. Thin 5% by volume with tap water on hot days.
Roller: Ready for use when mixed. Lambwool or mohair types are preferred.
Coats Required
Apply three finishing coats to new surfaces to achieve a closed film and solid colour.

Health & safety

For detailed safety information refer to Material Safety Data Sheet.
Keep out of reach of children.
Store away from direct sun, heat and severe cold, and avoid naked flames or sparks.
Ensure good ventilation during application and drying.
Non-flammable.

The cured film is non-toxic (contains no lead or other toxic chemicals)

Environmentally friendly

Equipment is cleaned with water

Almost odourless during application and curing

The substrate can be damp – concrete need not be fully cured before application.

Non-specialist application – can be applied by the average “do-it-yourselfer”

Water-based

Resistant to fresh and salt water + oils and chemicals when fully cured – withstands continuous immersion up to 60°C

Withstands nuclear radiation and is easily decontaminated

Completely free of Mesityl Oxide and is therefore approved for use in breweries

Health and safety

Download PDF

Tips & Advice

PRECAUTIONS:

Ensure that surfaces are thoroughly dry, sound and free from dust, dirt, grease and oil. Do not apply during wet weather. Do not apply directly to bare metal surfaces. Equipment and brushes must be cleaned immediately with tap water. Only suitable for interior use – the film tends to yellow and chalk on exterior exposure. Not suitable for direct application to powdery or friable surfaces whether previously painted or not.

STORAGE:

Store in a cool, dry, well ventilated place protected from moisture, away from sources of heat, ignition and direct sunlight. Containers which are opened should be properly resealed and kept upright to prevent leakage.

For more details refer to the technical data sheet.

Product Features